TIMBER WOLF BAND SAW BLADES (AVAILABLE IN ANY LENGTH)
We are the only U.S.A. company to package, rustproof, and re-temper the welds after being ground.
***MOST BLADES ARE CUSTOM MADE AND SHIP AS SOON AS WE'RE ABLE - USUALLY WITHIN A WEEK.***
PS Wood Machines has the most reliable high performance band saw blade you'll ever use!
HERE'S WHY:
1. Made from high silicon, low carbon steel, PS Wood Machines' band saw blades run cooler and last longer.
2. Milled teeth makes them ideal for resawing thick stock because these blades are true tracking and DO NOT WANDER.
3. Run under low tension, and thus require less horsepower from your band saw.
4. These blades produce a thin kerf and can make remarkably tight turns.
5. The weld on these blades is warranted.
? Puzzled about which Timber Wolf blade to use ? PC=Positive CLaw
AS=Alternate Set
AS-S=Alternate Set Special
VPC = Variable Positive Claw
RK=Raker
HP=High Performance
PC SERIES - for kiln dried wood available in: 3/16" to 1" wide in many tooth pitches
Most of us would like to keep the tedious labor of planing or sanding to a minimum. Our PC Series of blades is our claim to fame. It is, in its design, everything a wood cutting blade was meant to be. It has over 60% of the speed capabilities that a hook is able to travel at, while at the same time giving you the great finish of a skip. By incorporating a "hook" style geometry in our gullet, we have given our blade the ability for fast chip removal. Due to its round design we have eliminated any work hardening zones in the gullet. Couple all this with our unique 6.5 degree rake angle, combined with our special 5 tooth set pattern (which allows us to reduce the set) and we now have a true "thin kerf", awesome cutting blade that gives you an excellent finish.
AS SERIES - for green or exotic wood available in: 3/8" and 1/2" x 3 tpi
These small blades are unique in their body thickness, set, and rake angle. They are .032 thick, have an alternate set and a unique rake angle of 8.5 degrees. They also utilize the unique geometry of our PC gullet. These bands are primarily used in furniture industry. They have been designed to cut both fast and accurately in very thick wood such as stacked lumber. Woodturners use these blades to cut turnings out of large burls. Their applications are endless. Their performance is excellent if the thickness of your material exceeds 6 to 8 inches. These blades are not meant to be used on any 3-wheel saw or for that matter any saws with less than a 90" blade length or wheel diameter less than 14".
AS-S SERIES - for straight line veneer cutting available in: 3/4" x 3 tpi
This blade's uniqueness lies in the fact that it isonly .025 thick with our unique set pattern. The total overall set is less than .048 thousandths of an inch. When you are resawing very expensive woods that are thick and you want as thin a kerf as possible, a super finish, and you are not concerned with speed, this is the blade for you.
VPC Series - for straight-line resawing in small to large boards, kiln and air dry, up to 12" wide available in: 3/4" x 2/3 tpi
The variable tooth design reduces resonance throughout the blade; this combined with diffrent size teeth produces a very clean finish almost polishing the wood as it is cut. It is only .025 thick with an overall kerf of .049 and incorporates the unique geometry of our PC design.
RK & HP Series - for detail work These blades have a very thin kerf and 0 degree rake angle and are specifically designed for detail work in 1" and smaller kiln dried wood when a very clean finish is required. They are also very effective in plywood, particle-board and other similar products where tear-out is a concern. These blades can also be used to cut soft metals.
Categories
Default
Your cart
Authentication